Creality CR10S: Difference between revisions
m (→Operator's Log) |
m (→Operator's Log) |
||
| Line 73: | Line 73: | ||
Although it was once an issue, it is no longer an issue. Do not place stress onto the USB connector and always check the print area for things that may come into contact with the printer while it is in motion. | Although it was once an issue, it is no longer an issue. Do not place stress onto the USB connector and always check the print area for things that may come into contact with the printer while it is in motion. | ||
==== 2022-12-06 [[User:Blu | Brandon]] ==== | |||
The last print performed yesterday at 2022-12-05 23:50 did not succeed. The filament was not loaded during the print, and a first-layer inspection was not completed. | |||
Nozzle is further from the printer platform than normal. This may be the result of a previous maintenance action on the 3d printer or from a previous operator failing to save the printer bed leveling data into EEPROM. | |||
[[Category:3D_Printers]] | [[Category:3D_Printers]] | ||
Revision as of 03:03, 7 December 2022
| Creality-CR10S |
|---|
|
|
| 3D Printer |
|
Brand: Creality
Materials: ABS, PLA, PETG |
History
The Creality-CR10S was donated by Kyle. Thanks.
The glass build bed was donated by Michael.
Hotend
The hotend was previously clogged with a giant blob of PLA. Please watch your prints through the first layer at least. Not all prints will succeed, but you are more likely to succeed after the first layer is printed.
The thermistor on the hotend was replaced on 2022-07-20. Problems were noted in June.
Bed
The build surface was blue tape when the printer was first donated. The build surface was the Creality "Carborundum" tempered glass bed. As of 2022-08-22, the bed is binder-clipped, PEI coated steel.
Operator's Log
2022-08-26 Yangbot, entered by Brandon
Bed adhesion issues noted when printing bike handlebar spacers.
2022-08-28 Brandon
Bed adhesion issues confirmed.
Bed leveling was completed successfully, but there is a significant dip in the center and center, right side of the 3d printer bed. Bed leveling shows concerning data:
| 0.2mm leveling data | ||
|---|---|---|
| 0.225 | 0.225 | 0.275 |
| 0.225 | -0.050 | 0.000 |
| 0.275 | 0.250 | 0.300 |
2022-09-02 Brandon
Nozzle was severely clogged with burnt plastic. Nozzle replaced.
The clogged nozzle could have caused the issues on 2022-08-26, but a bed leveling was also performed. Additionally, extrusion on the first layer is increased to 120%.
2022-09-03 Brandon
Bed leveling completed and bike handlebar adapter from Thingiverse successfully printed.
The bed is still severely unlevel in the middle and center-right corner.
In order to adhere to the rough PEI surface, the printer was leveled 0.1mm lower than the measured height. This is done so that the first layer of extruded plastic will flow around the rough PEI coated texture on the bed and create a stable mechanical bond.
2022-11-30 Betsy, entered by Brandon
USB port broken during printer shuffling and repaired/replaced by the yangbot.
Although it was once an issue, it is no longer an issue. Do not place stress onto the USB connector and always check the print area for things that may come into contact with the printer while it is in motion.
2022-12-06 Brandon
The last print performed yesterday at 2022-12-05 23:50 did not succeed. The filament was not loaded during the print, and a first-layer inspection was not completed.
Nozzle is further from the printer platform than normal. This may be the result of a previous maintenance action on the 3d printer or from a previous operator failing to save the printer bed leveling data into EEPROM.