Kossel Delta 3D Printer: Difference between revisions
Timothytam (talk | contribs) (Added ABS as approved material. Added note on bed leveling w/o permission) |
mNo edit summary |
||
| (15 intermediate revisions by 2 users not shown) | |||
| Line 2: | Line 2: | ||
|+Kossel 3D Printer | |+Kossel 3D Printer | ||
|[[File:Kossel2.jpeg|300px]]<br/> | |[[File:Kossel2.jpeg|300px]]<br/> | ||
'''Location:''' | '''Location:''' Sold <br/> | ||
'''Ownership:''' Brandon Lu <br/> | '''Ownership:''' (previously Brandon Lu) <br/> | ||
'''Status:''' | '''Status:''' Sold <br/> | ||
'''Usage Restrictions:''' | '''Usage Restrictions:''' Not at space <br/> | ||
'''[[Printer Qualification Level]]:''' A | |||
|- | |- | ||
!3D Printer | !3D Printer | ||
| Line 14: | Line 15: | ||
|- | |- | ||
|} | |} | ||
RepRap Kossel printer on loan from Brandon Lu. | RepRap Kossel printer previously on loan from Brandon Lu | ||
== Getting Started == | |||
An in-person tutorial is possible and required by [[User:BLu]] before use of the printer. | |||
== General Advice and Precautions == | == General Advice and Precautions == | ||
=== Precautions === | === Precautions === | ||
====Cooling==== | ====Cooling==== | ||
Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer accepts fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up. | Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer accepts fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up. | ||
<nowiki>M106 S51</nowiki> | |||
=== Directions === | === Directions === | ||
| Line 44: | Line 44: | ||
<br />Baudrate: 250000 | <br />Baudrate: 250000 | ||
=== Printer Profiles === | === Printer Profiles === | ||
These settings may or may not appear depending on your slicing software. Attempt to apply these settings. | |||
==== Print bed & build volume ==== | ==== Print bed & build volume ==== | ||
Form Factor: Circular<br /> | Form Factor: Circular<br /> | ||
Origin at center: Checked<br /> | |||
Heated Bed: Checked<br /> | Heated Bed: Checked<br /> | ||
Diameter (X/Y | Diameter (X/Y): 200mm<br /> | ||
Height (Z): 260mm<br /> | Height (Z): 260mm<br /> | ||
G-code flavor: Marlin | |||
==== Axes ==== | ==== Axes ==== | ||
Maximum Feed Rate (X, Y, Z, E): 6000, 6000, 6000, 300<br /> | Maximum Feed Rate (X, Y, Z, E): 6000, 6000, 6000, 300<br /> | ||
Invert Control: Unchecked | Invert Control: Unchecked | ||
==== Start G-code ==== | |||
This code runs after the printbed and extruder are heated. Since the extruder heats relatively quickly, the thermal mass of the heatsink is enough to stave off malfunctions. | |||
<nowiki> | |||
G28 ;Home | |||
M106 S51 ;Turn on fan. Only line not in the stock startup G-code. | |||
;Prime the extruder | |||
G92 E0 | |||
G1 F200 E3 | |||
G92 E0</nowiki> | |||
==== Stop G-code ==== | |||
<nowiki> | |||
M106 S51 ;Keep fan running. Only line not in the stock end G-code. | |||
M104 S0 ;hotend off | |||
M140 S0 ;bed off | |||
;Retract the filament | |||
G92 E1 | |||
G1 E-1 F300 | |||
G28 X0 Y0 | |||
M84</nowiki> | |||
==== Cooling ==== | |||
Enable Print Cooling: Checked<br /> | |||
<span style="color:#ff0000">Initial Fan Speed: 20%</span> | |||
== Materials == | == Materials == | ||
PLA & | PLA & ABS: Preferred materials for this printer<br /> | ||
TPE / TPC: Flexible filaments will not work reliably with Kossel printer since the printer has a bowden-tube extruder. | TPE / TPC: Flexible filaments will not work reliably with Kossel printer since the printer has a bowden-tube extruder. | ||
== History == | == History == | ||
=== Gallery === | |||
<gallery> | |||
File:Kossel.jpeg|Top-down shot of printer | |||
File:Kossel2.jpeg|Benchy on printer | |||
File:Kossel3.jpg|Printer on Bench | |||
File:Kossel4.jpg|Printer LCD Screen | |||
</gallery> | |||
=== Head clogs === | === Head clogs === | ||
The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs. | This printer requires specialty configuration to keep the fan spinning while the extruder is heated. Do '''not''' print without the fan running. The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs. | ||
=== OfferUp and Selling === | |||
The printer was sold on offerup for $100. | |||
== Lending Terms == | == Lending Terms == | ||
| Line 67: | Line 103: | ||
Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt alterations or repairs on the printer. | Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt alterations or repairs on the printer. | ||
Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt to change filament on the printer. (Soon to change) | Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt to change filament on the printer. (Soon to change) | ||
{{3D_DigitalFabrication}} | |||
Latest revision as of 12:06, 26 July 2022
 Location: Sold |
| 3D Printer |
|---|
| Type: Reprap - Kossel Build Volume: Diameter: 200mm, Height: 260mm |
RepRap Kossel printer previously on loan from Brandon Lu
Getting Started
An in-person tutorial is possible and required by User:BLu before use of the printer.
General Advice and Precautions
Precautions
Cooling
Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer accepts fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up.
M106 S51
Directions
The Octoprint server can be reached at http://192.168.254.95 Login credentials can be found on the printer.
Slicing with Octoprint (easiest)
- Click "Upload" button
- Select the file you want to upload
- In the "Slicing *file you selected*" prompt, select slicing profile (Kossel, Kossel Support 1, Kossel Support 2). Support 1 generates support material only where the part overhangs above the bed while support 2 also generates support material where the part overhangs above itself.
- Click the "Slice" button.
- In the "files" section click the .gco file you just created.
- Click "GCode Viewer" tab on right half of the screen to view the slicer output. Layers can be viewed by dragging the sliders adjacent to the simulated platform area or by clicking the buttons.
- If you are satisfied with the slicer output, click "Print" in the "State" section of the page.
- The printer will initiate printing.
Configuration
This is for setup. Under normal circumstances, there is no need to modify these values.
Serial Connection
Serial Port: Auto
Baudrate: 250000
Printer Profiles
These settings may or may not appear depending on your slicing software. Attempt to apply these settings.
Print bed & build volume
Form Factor: Circular
Origin at center: Checked
Heated Bed: Checked
Diameter (X/Y): 200mm
Height (Z): 260mm
G-code flavor: Marlin
Axes
Maximum Feed Rate (X, Y, Z, E): 6000, 6000, 6000, 300
Invert Control: Unchecked
Start G-code
This code runs after the printbed and extruder are heated. Since the extruder heats relatively quickly, the thermal mass of the heatsink is enough to stave off malfunctions.
G28 ;Home M106 S51 ;Turn on fan. Only line not in the stock startup G-code. ;Prime the extruder G92 E0 G1 F200 E3 G92 E0
Stop G-code
M106 S51 ;Keep fan running. Only line not in the stock end G-code. M104 S0 ;hotend off M140 S0 ;bed off ;Retract the filament G92 E1 G1 E-1 F300 G28 X0 Y0 M84
Cooling
Enable Print Cooling: Checked
Initial Fan Speed: 20%
Materials
PLA & ABS: Preferred materials for this printer
TPE / TPC: Flexible filaments will not work reliably with Kossel printer since the printer has a bowden-tube extruder.
History
Gallery
Top-down shot of printer
Benchy on printer
Printer on Bench
Printer LCD Screen
Head clogs
This printer requires specialty configuration to keep the fan spinning while the extruder is heated. Do not print without the fan running. The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs.
OfferUp and Selling
The printer was sold on offerup for $100.
Lending Terms
Kossel Delta is currently on loan from User:BLu, hereinafter referred to as "owner."
Any member or visitor of MAG Laboratory, heinafter referred to as "user," may use the printer given the included configurations and with modifications of these printer configurations. Users excluding qualified 3d printer maintainers as defined by the owner shall not attempt alterations or repairs on the printer. Users excluding qualified 3d printer maintainers as defined by the owner shall not attempt to change filament on the printer. (Soon to change)
RepRap Mendel 3D Printer
