K40 Laser Cutter: Difference between revisions
m (→Air Assist Upgrades: added link to the drag chain stl) |
|||
| Line 89: | Line 89: | ||
=== Air Assist Upgrades === | === Air Assist Upgrades === | ||
[[File:K40DragChainBracket.stl]] | [[File:K40DragChainBracket.stl]] | ||
[[:File:K40DragChainBracket.stl]] | [[:File:K40DragChainBracket.stl]] | ||
Revision as of 21:00, 25 January 2024
 Location: Electronics Room |
| Laser Cutter |
|---|
|
Brand: Chinesium |
Getting Started
Welcome on your laser cutter journey. We at MAG Laboratory are proud to host the venerable and storied K40 laser cutter machine. As we should all know, each K40 machine is a unique snowflake upon this world not only because each factory K40 is manufactured differently but also because each K40 owner will apply different modifications to their machine.
Read at least the "General Use" section of the K40 user manual (link).
General Advice and Precautions
⚠ Always use the air assist.
⚠ Always operate with lid closed.
⚠ Do not let machine "run dry."
⚠ Do not place hand along laser path.
⚠ Ensure laser cooling water temperature is acceptable.
Software Support
The preferred file format is .svg. Inkscape (link) can be used to create and edit svg files it is under active development, so be sure to update your inkscape.
Materials
Recommended Materials
| Material | Comment |
|---|---|
| Acrylic | Cuts well. Turns into combustion byproducts immediately! |
| MDF | Mostly turns into smoke. Ash may be an issue. Use air assist to clear the ash. |
| Laser Rubber | Ash may be an issue. Use air assist to clear as much ash as possible. |
| Acetal Plastic | Apparently works if the plastic has additives. |
| Leather | Cuts / Engraves. |
Banned Materials
| Material | Comment |
|---|---|
| PVC | Combustion byproducts are literally hydrochloric gas. Do not cut. |
History
The K40 is a complex machine with a history of previous activity. Delve into the mysteries of this delightful machine here.
Gallery
Lid On
Interior (pre-air-assist)
Cutting Neoprene
Interior (with air-assist)
Cutting Assembly in the K40
CO2 Laser Tube
Laser Power Supply
Laser Cutter Control Boards
Laser Cutter Open
Interior (air assist)
Air Assist Pump
Water Temperature Thermometer
Aluminum Air Assist
2021-05-03 "Cloudray" aluminum air assist nozzle installed
Laser Tube
The laser tube was replaced after being broken from a loss of cooling incident on 2021-03-17.
Laser Path
The focusing mirror was broken on 2021-01-26 and subsequently replaced on 2021-02-01.
Air Assist Upgrades
User:BLu added a drag chain for the air assist on 2021-01-24.
The air assist pump and PLA nozzle were installed on 2021-01-31.
Alignment
User:BLu first aligned the laser on 2020-12-24.
Acquisition
The K40 laser cutter was purchased by User:BLu on 2020-12-03 and arrived at MAG Laboratory on 2020-12-07.
Laser Guidance
2023-12 Two visible lasers are installed to denote the cutting location of the CO2 laser. The two lasers form a crosshair that marks the location where the CO2 laser beam should hit.
The files for the laser bracket with laser guidance can be found at https://github.com/blu006/blu_BOB_and_MISC/tree/main/2023/laser_bracket
The only vitamins are the existing M3 mounting screws that came with the k40, a square screw, and an M3 internal hex socket head bolt.
Future Upgrades
The K40 is due for many future upgrades including but not limited to:
- height adjustable table